How To Extend The Gas Line For Dryer | Following Easy Methods

It is very important to select the correct gas connector for your gas appliances like dryer, oven, stove, etc. for proper appliance operation and gas safety. You need to know the maximum input rating of the appliance you’re installing.

This will determine how large of a gas connector you need for the appliance. If you are looking for answers to How to Extend The Gas Line for Dryer, then you have to know about the basics of connectors and tips before selecting one. 

How To Extend The Gas Line For Dryer

Firstly, the gas line connector for any appliance depends on the input rating of how much gas your appliance consumes in an hour at full capacity. This information can be found on the manufacturer’s tag on the appliance or in the owner’s manual. 

How To Extend The Gas Line For Dryer

Secondly, you need to measure the distance from the gas supply stub out to the gas inlet of the appliance. Make sure to add enough length to allow you to move the appliance for maintenance and repair without stretching the connector.

If you want to extend the gas line for your dryer or any other appliance you can use a 48-inch connector. Two feet is the least required amount for the depth of the cabinetry and an additional two feet to safely move the appliance to get behind it. 

This sizing also goes for a dryer. If you choose a gas pipe that is in total 4 feet long this will help you move or extend the gas line comfortably. 

Consult the connector capacity chart located on the gas connector bag or product label. Using this chart, you can select the gas connector, pipe, and other necessary things greater than or equal to the appliance and matches the connector length you need. 

Once you identify the size of the gas connector you’ll need to determine what end fittings are required to connect to the appliance and gas supply. Check if there is a manual gas shutoff valve installed at the appliance. If yes identify the outlet type and size. If not one must be installed. 

It is also very important to identify what is the thread type and size of the gas inlet on the appliance. It will either have a male stub out which has external threads or a female inlet which has internal threads. It may even have a pre-installed fitting that you need to connect to. You’ll have to match the end fittings of the dryer’s connector to the two connecting points- the appliances gas inlet and the gas shutoff valve. 

Gas Dryer Installation

To start with the installation process, tip the dryer backward and rest it on a large piece of cardboard to help prevent floor damage. Using an adjustable wrench and tape measure screw the leveling legs into the lake holes until the bottom of the foot is approximately a half-inch from the base of the dryer. 

Return the dryer to its upright position. Gently glide the dryer until it is close to its conclusive area. But leave enough room to connect the exhaust vent. An adjustable stainless steel gas connector is suggested to secure the gas supply line and valve to the dryer.

Extract the red cap from the gas pipe on the rear panel of the dryer. You can connect the flexible gas connector to the dryer gas pipe using a pipe to flare adapter fighting or use a pipe elbow and adapter fighting to direct the gas connector up or to either side. Be aware you’ll need to use pipe joint compound on the threads of all non-flared male fittings.

Once the gas connector has been secured, open the gas shutoff valve and test all the connections by applying a non-corrosive leak detection solution. The solution will gurgle if there is any leak.  Any leaking connection should be corrected. 

To reduce the risk of fire the dryer must be exhausted outdoors refer to the vent system charts in the installation manual to determine the number of vent sections and elbow joints required.  

For the venting to reach the outside of the home an exhaust hood will need to be installed over the vent on the home exterior wall positioned at least 12 inches from the ground. If the dryer model uses steam your next step is to turn the cold water faucet off and disconnect the washer inlet hose from the faucet port. Connect the exhaust outlet and move the dryer to its exact place. Check if the dryer is level.

You might also like

Final verdict

This way you can install your gas dryer in any location of your house and never have to think about how to extend the gad line for the dryer because now you know how easy it is to find that out. 

Frequently Asked Questions (FAQ)

What Is The Longest Gas Line For Dryers?

If your clothes dryer is taking forever to dry a load of laundry, it may have a clogged gas line. The gas line is the supply line that feeds natural gas to the dryer. Over time, lint and other debris can build up in the line and cause a blockage. A clogged gas line not only lengthens drying time, but it can also be a fire hazard.

If you suspect your gas line is clogged, inspect it for signs of blockage. Look for lint or other debris around the connection point where the gas line meets the dryer. If you see any, use a brush or vacuum to remove it. If the line is still clogged, you may need to call a professional to clear it.

A clogged gas line is not the only thing that can lengthen drying time. Other potential problems include a faulty igniter, a clogged vent, or a dryer that is too full. If your dryer is taking longer than usual to dry clothes, troubleshoot the problem to identify the cause.

Can I Connect 2 Gas Hoses Together?

If you have two gas hoses and you want to connect them together, you can do so by using a gas hose connector. This will allow you to connect the two hoses together so that gas can flow through both of them. Make sure that you have a gas hose connector that is the right size for the hoses that you are using.

What Size Gas Line Is Required For A Dryer?

A dryer typically requires a gas line with a diameter of 3/4 inches. However, it is always best to consult with a certified installer or your local gas company to determine the specific requirements for your home.

I'm Jimmy, the creative mind behind AskingCenter.com. Drawing from extensive expertise in home improvement, I founded this platform to help individuals transform their living spaces. My dedication lies in empowering homeowners with dependable advice, ensuring that every DIY project not only elevates your home but also enhances your lifestyle. Join me as we redefine homes, one project at a time.

0 0 votes
Article Rating
Subscribe
Notify of
guest

0 Comments
Oldest
Newest Most Voted
Inline Feedbacks
View all comments
0
Would love your thoughts, please comment.x
()
x